• Cast alluminium motor housing
• Cast alluminium end housing
• Alluminium drum casting
• Latch spring and retainer clip
• Set of drawings

• Kit 1 plus
• Bearings
• KK25 sprag bearing

• Kit 1 plus
• Castings finished machined
• Latch pin assembly fitted
  

• Kit 3 plus
• Bearings
• KK25 sprag bearing
• Sprag Latch Ring

1303 self aligning bearings

$20 ea.

KK25 sprag bearing

$70 ea.

Frame, powder coated

$126 ea.

150A cont. silver contact solenoid

$130 ea.

Latch knob

$12 ea.

Latch ring

$30 ea

Latch pin assembly complete

$27 ea.

OJOP Snap action battery connectors.

$30 pr.

Battery leads complete 30 cm

$45 pr

Foot switch, plug and socket

$35 ea.

Kit 1

This is the most basic kit.

You must provide the following components: Bosch GF motor, solenoid, battery cables and connectors, bearings, sprag, sprag ring, latch materials, frame, foot switch and connectors, turnaround pulley, mono filament line, parachute and battery.

You must do the following work: Machine the motor end housing, machine the sprag end housing, machine the drum, machine the latch components, machine the motor shaft and fit a sleeve to it then finish machine the sleeve, machine the sprag ring, make the frame, make up the battery cables, assemble the components, make a turnaround pulley and test the winch with FAI tester if you intend to use it at National or International level.

You must have access to the following equipment: Lathe, milling machine, drill press, cable crimping tool or soldering equipment, assembly press.

Optional: Knurling tool, FAI winch testing equipment.

Top of Page

Kit 2

This is the most basic kit with the addition of bearings.

You must provide the following components: Bosch GF motor, solenoid, battery cables and connectors, sprag ring, latch materials, frame, foot switch and connectors, turnaround pulley, mono filament line, parachute and battery.

You must do the following work: Machine the motor end housing, machine the sprag end housing, machine the drum, machine the latch components, machine the motor shaft and fit a sleeve to it then finish machine the sleeve, machine the sprag ring, make the frame, make up the battery cables, assemble the components, make a turnaround pulley and test the winch with FAI tester if you intend to use it at National or International level.

You must have access to the following equipment: Lathe, milling machine, drill press, cable crimping tool or soldering equipment, assembly press, electric drill.

Optional: Knurling tool, FAI winch testing equipment.

Top of Page

Kit 3

Castings supplied finished machined.

You must provide the following components: Bosch GF motor, solenoid, battery cables and connectors, bearings, sprag, sprag ring, frame, foot switch and connectors, turnaround pulley, mono filament line, parachute and battery.

You must do the following work: Machine the motor shaft and fit a sleeve to it then finish machine the sleeve, machine the sprag ring, make the frame, make up the battery cables, assemble the components, make a turnaround pulley and test the winch with FAI tester if you intend to use it at National or International level.

You must have access to the following equipment: Lathe, milling machine, cable crimping tool or soldering equipment, assembly press, electric drill.

Optional: FAI winch testing equipment.

Top of Page

Kit 4

Just add motor, electricals and frame.

You must provide the following components: Bosch GF motor, solenoid, battery cables and connectors, frame, foot switch and connectors, turnaround pulley, mono filament line, parachute and battery.

You must do the following work: Machine the motor shaft and fit a sleeve to it then finish machine the sleeve, make the frame, make up the battery cables, assemble the components, make a turnaround pulley and test the winch with FAI tester if you intend to use it at National or International level.

You must have access to the following equipment: Lathe, cable crimping tool or soldering equipment, assembly press, electric drill.

Optional: FAI winch testing equipment.

Top of Page